Skip to content
Repair Guides

Samsung Galaxy A17 Battery Replacement

Moderate45–60 min12 steps

Over time, lithium-ion cells degrade, resulting in rapid battery drain, random shutdowns during resource-heavy tasks, or battery swelling that pushes the back panel outward. Replacing the 5000 mAh battery restores dependable all-day performance and prevents safety hazards associated with aged cells. This procedure involves softening the perimeter adhesive, unclipping the structural midframe, and safely releasing the bonded battery from the chassis.

Required Tools

  • Heat gun or heated pad (set to 70°C to 80°C)
  • Suction handle
  • Thin plastic opening picks
  • Nylon spudger
  • Phillips #00 precision screwdriver
  • SIM card tray ejector tool
  • Isopropyl alcohol (90% purity or higher)
  • Replacement battery adhesive strips or precut rear adhesive
  • Safety glasses and ESD-safe mat

Step by step

  1. 1

    Step 1: Power Off the Device and Remove the SIM Tray

    Turn off the Galaxy A17 completely to avoid electrical shorts during disassembly.

    Insert a SIM eject tool into the small hole on the upper side rail, pop out the SIM card tray, and set it aside.

  2. 2

    Step 2: Heat the Rear Panel

    Place the phone face-down on a heating pad or use a heat gun around the outer edges of the back panel for 2 to 3 minutes at roughly 75°C.

    This softens the factory adhesive holding the rear cover against the internal frame.

  3. 3

    Step 3: Separate the Rear Cover

    Press a suction cup near the bottom edge of the back cover and pull gently upward to create a small gap.

    Slide a thin plastic pick into the seam and carefully work your way around the perimeter to cut through the adhesive, taking care around the camera lenses.

  4. 4

    Step 4: Lift Away the Back Panel

    Gently lift the back panel off the phone body once the adhesive is fully severed.

    Clean away any adhesive residue along the perimeter of the frame and rear panel using a lint-free cloth lightly dampened with isopropyl alcohol.

  5. 5

    Step 5: Extract the Midframe Screws

    Locate all the Phillips #00 screws securing the plastic midframe and motherboard shield.

    Remove each screw carefully and organize them on a magnetic mat, as internal screws must return to their exact locations during reassembly.

  6. 6

    Step 6: Unclip and Remove the Midframe

    Insert a plastic pry tool into the seam between the midframe and the front frame assembly.

    Work around the edges to disengage the plastic perimeter clips, then lift the midframe away to expose the motherboard, battery, and lower sub-board.

  7. 7

    Step 7: Disconnect the Battery and Interconnect Cables

    Use the flat end of a plastic spudger to pry the battery flex cable directly off the motherboard connector to cut power immediately.

    Disconnect and fold back the display and main-to-sub interconnect flex cables that route across the top of the battery pack.

  8. 8

    Step 8: Release the Battery Adhesive

    Grasp the adhesive pull tab on the battery pouch and pull it outward at a low, steady angle.

    If the tab tears or the phone uses standard adhesive strips, introduce a few drops of isopropyl alcohol along the battery edges and wait 2 to 3 minutes to soften the glue.

  9. 9

    Step 9: Extract the Old Battery

    Slide a wide plastic pry card or flat spudger underneath the battery cell and gently lever it upward from the chassis.

    Never use metal tools, sharp implements, or aggressive prying, as puncturing a lithium pouch can trigger chemical combustion.

  10. 10

    Step 10: Seat the New Battery

    Remove any residual glue from the battery well, apply fresh double-sided mounting adhesive, and lay the new battery into the bay.

    Connect the battery terminal momentarily to verify alignment before pressing it down firmly, then disconnect it again to complete the rest of the assembly safely.

  11. 11

    Step 11: Reconnect Cables and Reinstall the Midframe

    Reconnect the display and interconnect flex cables, followed by the battery terminal connector.

    Position the midframe over the chassis, snap the perimeter clips back into place with gentle thumb pressure, and fasten all Phillips #00 screws securely.

  12. 12

    Step 12: Reseal the Back Cover and Test

    Apply a new perimeter adhesive gasket to the phone frame, align the rear cover, and press firmly along all edges to ensure a tight seal.

    Reinsert the SIM tray, power on the device, and connect a charger to verify proper charging functionality.

Safety

Would you rather leave the repair to the experts?

Disclaimer: repairs are done at your own risk. Devices contain batteries and live components; improper handling can cause injury or fire. For a safe, warrantied repair, contact us.

Frequently asked questions

Use the phone normally until the charge drops to approximately 5%, then connect it to an original 25W wall charger. Charge the device continuously to 100% and leave it connected for at least one additional hour so the battery management controller can map the full capacity range accurately.

Do not pry against the cell with metal tools. Apply a small amount of 90% or higher isopropyl alcohol around the gap between the battery and the frame, let it sit for a couple of minutes to break down the adhesive bond, and gently work a flexible plastic card underneath to free the battery.

Check whether the battery connector and the main board flex cables are seated completely flat in their sockets. If the connectors are fully seated, plug the phone into a known working charger for 15 to 20 minutes, as replacement batteries are often stored at low storage voltages and require an initial charge cycle to boot.

If you encounter a stripped screw, torn ribbon cable, or feel uncomfortable handling delicate internal parts, stop the repair immediately. You can reach out to professional technicians by submitting an inquiry through KRON's contact form for further assistance.

Back to Guides

  • 12-month warranty
  • Original (OEM) parts
  • Your data kept confidential
  • You approve the price before the repair
  • 3,486+ devices per month