Skip to content
Repair Guides

Samsung Galaxy A17 Screen Replacement

Moderate45–60 min11 steps

A screen replacement is necessary when your Samsung Galaxy A17 exhibits cracked front glass, unresponsive touch zones, colorful vertical lines, or a blank display following an impact. Replacing the screen restores touch accuracy and original visual output to the smartphone. During this repair, you will open the rear cover, remove the midframe to access the internal hardware, isolate the power source, and seat a fresh display assembly.

Required Tools

  • Heat gun or temperature-controlled heating pad
  • Phillips #00 precision screwdriver
  • Plastic opening picks and thin spudger
  • Suction cup handle
  • Curved precision tweezers
  • Isopropyl alcohol (90% or higher) and lint-free wipes
  • T-7000 liquid adhesive or precut adhesive strips
  • Anti-static wrist strap

Step by step

  1. 1

    Step 1: Power Down and Eject SIM Tray

    Turn off the Samsung Galaxy A17 completely to avoid short circuits.

    Insert a SIM ejector pin into the small hole on the card tray, apply gentle pressure until the tray releases, and pull it out of the frame.

  2. 2

    Step 2: Heat and Remove the Back Cover

    Warm the perimeter of the back panel using a heat mat or heat gun set to 75°C for two minutes to soften the adhesive.

    Attach a suction cup to the lower rear area, pull upward to create a slight gap, insert a plastic opening pick, and cut through the adhesive along the edges to release the cover.

  3. 3

    Step 3: Unscrew the Midframe

    Locate and remove all the Phillips #00 screws securing the plastic internal midframe to the phone chassis.

    Keep these screws neatly organized on a magnetic work mat so they return to their exact original positions.

  4. 4

    Step 4: Unclip and Detach the Midframe

    Slide a thin plastic pry tool between the outer edge of the screen frame and the inner bezel.

    Work around the entire boundary to release the plastic locking tabs, then lift the midframe away from the phone body.

  5. 5

    Step 5: Disconnect the Battery

    Prioritize safety by immediately disconnecting the battery flex cable before handling any other internal component.

    Use a non-conductive plastic spudger to gently lever the battery connector straight up from the motherboard.

  6. 6

    Step 6: Disconnect and Test the New Screen

    Disconnect the old display ribbon cable from the board.

    Connect the new replacement display temporarily, reattach the battery connector, and turn on the device to test touch sensitivity, color consistency, and brightness levels before proceeding with final installation.

  7. 7

    Step 7: Remove the Damaged Display

    Turn the phone off and unplug the battery once more.

    Apply heat around the perimeter of the front glass at 80°C for two to three minutes, slide an opening pick beneath the glass, slice the perimeter adhesive, and feed the display flex cable out through the frame slot.

  8. 8

    Step 8: Clean and Prepare the Housing Bezel

    Remove all leftover factory adhesive and glass fragments from the recessed channel using plastic scrapers and tweezers.

    Clean the channel thoroughly with a lint-free swab dipped in isopropyl alcohol so the new adhesive can form a solid bond.

  9. 9

    Step 9: Apply Adhesive and Seat the Display

    Lay a thin, continuous bead of T-7000 adhesive or install precut adhesive tape along the inner frame shelf, making sure not to obstruct the front camera or light sensors.

    Guide the new screen cable through the chassis opening, press the screen evenly into the frame, and verify that the glass sits flush.

  10. 10

    Step 10: Reconnect Cables and Reinstall the Midframe

    Press the display ribbon cable firmly into its socket until it clicks, then reconnect the battery.

    Position the plastic midframe over the assembly, snap the perimeter clips back into place, and secure all Phillips screws.

  11. 11

    Step 11: Reseal the Back Cover

    Apply fresh adhesive tape or liquid glue around the rear perimeter of the housing.

    Align the back cover, press it down firmly, and clamp the device gently with padded nylon clips or light rubber bands for 30 minutes to allow the bond to cure.

Safety

Would you rather leave the repair to the experts?

Disclaimer: repairs are done at your own risk. Devices contain batteries and live components; improper handling can cause injury or fire. For a safe, warrantied repair, contact us.

Frequently asked questions

A screen pre-mounted to a midframe requires transferring the motherboard, sub-board, and battery over to the new frame assembly. A bare screen panel without a frame involves less internal part transfers but requires you to cleanly unglue the old glass and adhere the new panel manually.

A screen replacement is strictly a hardware repair and does not alter stored files, photos, or accounts. Even so, creating a backup before undertaking any physical repair is strongly advised.

Launch the Samsung dialer keypad and type the diagnostic code *#0*# to open the hardware test utility. Select the Touch tile and drag your finger across all screen sections to verify every block registers input properly.

Power the phone off, unplug the battery, and reseat the display ribbon cable to ensure it is aligned squarely without bent pins. Reconnect the battery, plug in a charger to confirm adequate power, and restart the device.

If you encounter damaged connectors, persistent display glitches, or lack specialized heating equipment, you can reach out via KRON's contact form to have an experienced repair specialist assist you.

Back to Guides

  • 12-month warranty
  • Original (OEM) parts
  • Your data kept confidential
  • You approve the price before the repair
  • 3,486+ devices per month