Samsung Galaxy F08 Camera Replacement
Replace the camera if your Galaxy F08 shows a black screen in the camera app, shows a "Camera failed" error, can't focus, or produces hazy or streaked photos after a drop. Listings describe a 50 MP main and 2 MP secondary rear camera, an 8 MP front camera, a 6000 mAh battery and an IP64 rating. The guide shows how to remove the glued back cover and swap the camera module. The phone may no longer be as well protected against dust and splashes after you reseal it.
Required Tools
- Heat gun or iSmart heating pad (a hair dryer also works)
- Suction cup and thin plastic opening picks
- Plastic spudger (nylon, not metal)
- Phillips #00 screwdriver
- Anti-static tweezers
- SIM eject tool
- Isopropyl alcohol (90% or stronger) and lint-free wipes
- Replacement camera module that matches model SM-E085F
- Pre-cut back cover adhesive or a thin double-sided adhesive tape
- ESD wrist strap and a magnetic screw mat
Step by step
- 1
Step 1: Rule out software and the lens cover
Clear the Camera app's cache, restart in Safe Mode and test again.
Also check whether the outer lens glass is cracked, because a cracked lens cover is a cheaper fix than a new module.
Back up your data before you continue.
- 2
Step 2: Power down and prepare
Charge the battery to below 25% so that it carries less energy if it gets damaged by accident.
Then switch the phone off fully and remove the SIM/microSD tray.
Put on your ESD strap.
- 3
Step 3: Soften the back cover adhesive
Warm the edges of the back cover evenly to about 80 °C for one to two minutes.
Don't keep the heat on one spot.
Too much heat can warp the plastic cover or stress the battery.
- 4
Step 4: Open the back cover
Put the suction cup near the bottom edge, pull to make a small gap and slide in an opening pick.
Keep the pick shallow (no more than 3 mm) as you work around the edges.
Be extra careful near the camera island and the side buttons, where flex cables run close to the frame.
- 5
Step 5: Remove the midframe
Take out all the Phillips screws that hold the plastic midframe over the motherboard.
Put them on your mat in the same pattern so they go back in the same holes.
Gently pry the midframe off, starting at the top corners.
- 6
Step 6: Disconnect the battery first
Use the spudger to lift the battery connector off the board before you touch any camera cable.
If you skip this, you risk a short circuit that can damage the board or the new camera.
- 7
Step 7: Release the faulty camera
Find the rear camera connectors at the top of the motherboard and pry them straight up with the flat end of the spudger.
Lift the module out with tweezers by its edges or its metal frame.
Never press on the lens.
- 8
Step 8: Install the new module
Compare the new part to the old one: connector shape, flex length and lens position should all match.
Seat the module in its bracket, line up the connector and press down evenly with a fingertip until it clicks.
Pressing at an angle can bend the pins.
- 9
Step 9: Test before you close the phone
Reconnect the battery for a moment and power the phone on.
Test the main lens, the secondary lens, the flash, autofocus, video and the front camera.
If anything fails, power down, disconnect the battery and reseat the camera connector.
- 10
Step 10: Reassemble
With the battery disconnected again, check that no cable is pinched, then reconnect the battery.
Refit the midframe and put each screw back in its original hole.
- 11
Step 11: Reseal the back cover
Remove all the old adhesive with the alcohol and let it dry.
Apply new adhesive, press the cover on firmly and hold it under light, even pressure for a while.
Finish with a last camera test and put the SIM tray back.
Would you rather leave the repair to the experts?
Disclaimer: repairs are done at your own risk. Devices contain batteries and live components; improper handling can cause injury or fire. For a safe, warrantied repair, contact us.
Frequently asked questions
Not always. Clean the lens cover first, take the phone out of its case and test again. A cracked or scratched lens cover causes haze too and is a simpler repair. If autofocus hunts or never locks, the module itself is usually at fault.
Disconnect the battery and reseat the camera connector, checking for bent pins or debris. If the screen is still black, the replacement part may be faulty or meant for a different model.
Only if the seller confirms it fits the F08 (SM-E085F). Similar entry-level Galaxy phones can use a different connector pin count, flex shape or mounting, so a part that looks the same can still fail to fit or work.
Probably less than before. Even with fresh adhesive, a back cover you resealed at home rarely matches the factory seal, so keep the phone away from water afterwards.
A professional can confirm whether the module, the lens cover or the board is at fault before replacing parts. Use KRON's contact form to arrange a repair.
Only a few sources on this phone were found. One spec listing gave the hardware (Helio G99, 6.7" screen, 50 MP + 2 MP rear, 8 MP front, 6000 mAh, IP64). A SamMobile report gave the model number SM-E085F, from a GSMA database listing. No teardown of the F08 itself could be found. The opening and internal steps are based on how Samsung's similar budget phones like the Galaxy A07 are usually built: glued plastic back, midframe held by screws, cameras at the top of the board. Check the screw layout and connector positions on your own phone as you go.