Samsung Galaxy M08 Battery Replacement
Over time, lithium-ion cells naturally degrade, resulting in rapid power drain, unexpected shutdowns, or physical swelling that can distort the rear panel. Installing a fresh 6000 mAh cell restores original runtimes and protects against hazardous failure modes in aging hardware. This repair requires detaching the rear cover, lifting the protective internal midframe, and carefully dissolving battery adhesive without puncturing the pouch.
Required Tools
- Phillips #00 precision screwdriver
- SIM card tray ejector
- Plastic opening picks
- Nylon spudger
- Suction cup handle
- Heat gun or heating pad
- Isopropyl alcohol (90% or higher concentration)
- Pre-cut battery replacement adhesive strips
- Safety glasses
Step by step
- 1
Step 1: Power Down and Eject the SIM Tray
Shut down the Samsung Galaxy M08 completely before beginning any disassembly.
Insert your SIM ejector tool into the hole on the upper left side of the frame, depress the release pin, and pull the SIM tray completely out of the phone.
- 2
Step 2: Heat the Rear Housing
Apply heat evenly along the perimeter of the back cover using a heating pad or heat gun set to roughly 70°C for two to three minutes.
Warm the plastic cover gently to soften the adhesive seal without warping the exterior chassis.
- 3
Step 3: Unclip the Back Panel
Place a suction cup near the bottom edge of the phone, pull upward to create a small gap, and insert a plastic pick into the seam.
Slide the pick around the frame perimeter to pop the plastic retaining clips, taking care near the power button area.
- 4
Step 4: Extract the Midframe Screws
Remove all Phillips #00 screws securing the internal plastic midframe assembly over the motherboard and battery bay.
Organize the screws in a magnetic work mat so each fastener returns to its original position during reassembly.
- 5
Step 5: Remove the Midframe and Disconnect the Fingerprint Sensor
Use a nylon spudger to unhook the midframe clips from the chassis, pivoting the frame upward gently.
Disconnect the side-key fingerprint sensor ribbon connector from the motherboard before lifting the midframe away entirely.
- 6
Step 6: Disconnect the Battery Terminal
Always cut the power source before touching other internal hardware to prevent accidental electrical shorts.
Use the flat edge of a non-conductive plastic spudger to pry the battery flex cable straight up and off its board socket.
- 7
Step 7: Detach the Main Interconnect Cable
Unclip both ends of the wide flex cable that runs over the front of the battery to connect the motherboard to the lower daughterboard.
Lift the cable out of the chassis and set it aside in a dust-free area.
- 8
Step 8: Dissolve the Factory Battery Adhesive
Apply several drops of high-grade isopropyl alcohol along the gaps between the battery pouch and the frame to loosen the strong adhesive underneath.
Allow the chemical solvent to penetrate the adhesive strips for two minutes.
- 9
Step 9: Pry Out the Degraded Battery
Insert a wide plastic pry card underneath the battery from the outer edge, levering slowly and evenly.
Keep the pouch flat and never use metal tools, as bending or puncturing the lithium-ion cell can lead to smoke and fire.
- 10
Step 10: Seat the Replacement Battery
Wipe any lingering adhesive residue from the battery bay and apply fresh double-sided mounting tape.
Position the new battery into the housing, temporarily plugging in the flex connector to ensure perfect alignment before pressing the cell firmly into place.
- 11
Step 11: Reassemble Flex Ribbons and Midframe
Disconnect the battery connector briefly while you reconnect the lower daughterboard interconnect cable across the pack.
Reattach the fingerprint sensor ribbon, snap the midframe back onto the chassis, and tighten all Phillips screws securely.
- 12
Step 12: Reconnect Battery, Close Cover, and Test
Plug the battery cable securely into the motherboard, snap the rear cover back on with firm perimeter pressure, and reinstall the SIM tray.
Turn the device on to verify charging behavior and test device stability before handing it back into daily service.
Would you rather leave the repair to the experts?
Disclaimer: repairs are done at your own risk. Devices contain batteries and live components; improper handling can cause injury or fire. For a safe, warrantied repair, contact us.
Frequently asked questions
Discharge the newly installed battery down to roughly 5% through normal usage, then connect it to an original wall charger and let it reach 100% uninterrupted. Leave it connected to power for an additional hour to allow the system software to calibrate its charge tables.
Stop applying pressure immediately, step away, and transfer the phone to a well-ventilated, fire-safe area away from flammable materials. Never inhale vapors from a compromised battery pouch or expose a punctured lithium cell to water.
Check that the battery flex connector and the main interconnect ribbon are both seated squarely in their respective board sockets. If the phone still shows no signs of life, you can use KRON's contact form to consult an experienced technician.
No, you should only use high-purity isopropyl alcohol (90% or higher). Acetone dissolves phone plastics and ribbon cables, while low-concentration rubbing alcohol contains too much water, risking internal corrosion.
Sources