Samsung Galaxy S26 Plus Camera Replacement
This guide details the procedure for replacing a malfunctioning rear camera assembly in the Samsung Galaxy S26 Plus. You will need this repair if you experience persistent autofocus failure, blurred photos, cracked internal optics, or camera app crashes. Completing this repair involves softening factory water-resistant adhesive, removing the protective midframe shield, and safely handling sensitive CMOS sensor flex cables.
Required Tools
- Heat gun or heated mat
- Suction handle
- Plastic opening picks
- Phillips #00 precision screwdriver
- ESD-safe plastic spudger
- Precision tweezers
- Isopropyl alcohol (90% or higher) and lint-free cleaning cloth
- Pre-cut replacement rear glass adhesive
Step by step
- 1
Step 1: Power Down the Device
Turn off the Samsung Galaxy S26 Plus completely and remove the SIM card tray using an ejection tool.
Never work on a powered smartphone to avoid electrical shorts.
- 2
Step 2: Heat the Rear Panel
Apply uniform heat around the outer edges of the rear glass using a heat gun set to 80°C (175°F) for 2 to 3 minutes.
This softens the water-resistant adhesive holding the back cover without damaging internal components.
- 3
Step 3: Cut the Adhesive and Lift the Back Glass
Position a suction handle near the bottom edge of the back panel and pull upward to create a slight seam.
Insert a plastic opening pick and carefully slide it around all edges, keeping the pick shallow to avoid tearing internal flex ribbons.
- 4
Step 4: Remove the Upper Bracket Screws
Use a Phillips #00 screwdriver to extract the retaining screws securing the upper motherboard shield and wireless charging assembly.
Keep the screws organized in a tray so they return to their exact locations during reassembly.
- 5
Step 5: Detach the Wireless Charging Shield
Gently lift the plastic upper midframe bracket along with the integrated wireless charging coil away from the chassis.
Set the assembly aside in a clean, dust-free area.
- 6
Step 6: Disconnect the Battery
Insert the flat edge of an ESD-safe plastic spudger under the battery connector and pry it straight up from the motherboard.
Disconnecting power immediately ensures a safe workspace for component replacement.
- 7
Step 7: Disconnect the Camera Flex Cables
Identify the press-fit ribbon connectors for the rear camera sensors on the upper motherboard.
Use your plastic spudger to gently pop each camera connector straight up from its socket.
- 8
Step 8: Remove the Faulty Camera Assembly
Carefully lift the rear camera module out of its recessed frame compartment using blunt tweezers.
Avoid touching the exposed optical sensors or applying pressure to the delicate surrounding motherboard circuitry.
- 9
Step 9: Seat the New Camera Module
Place the replacement camera module into the frame housing, making sure it sits flush in its alignment tabs.
Align the flex ribbon connectors over their motherboard sockets and press down gently until you feel a firm click.
- 10
Step 10: Connect the Battery and Test
Snap the battery connector back into place, temporarily set the upper bracket down, and power on the phone.
Open the camera application to test the ultra-wide, wide, and telephoto sensors, ensuring autofocus and image stabilization work correctly.
- 11
Step 11: Reinstall the Upper Midframe Bracket
Power the phone off again, seat the wireless charging bracket into position, and press until its perimeter clips lock.
Reinstall and tighten all Phillips #00 screws evenly until snug.
- 12
Step 12: Reapply Adhesive and Seal the Back Panel
Clean away any residual adhesive on the frame and rear cover using isopropyl alcohol.
Apply new pre-cut adhesive, align the rear glass precisely over the frame, and apply firm, even perimeter pressure to seal the device.
Disclaimer: repairs are done at your own risk. Devices contain batteries and live components; improper handling can cause injury or fire. For a safe, warrantied repair, contact us.
Prefer to leave it to the pros?
Frequently asked questions
Depending on the replacement part sourced, individual camera sensors can be disconnected, or the entire linked triple-camera housing can be swapped as a complete unit.
Yes, opening the phone breaks the original factory IP68 seal. Installing fresh pre-cut adhesive restores everyday dust and splash resistance, but liquid submersion should be avoided.
Turn off the phone, disconnect the battery, and reseat each camera connector to ensure no pins are loose or misaligned. You should also clear the Camera app cache and data in the Android settings menu.
Basic camera functionality works immediately upon hardware installation, though rebooting the device and clearing the camera system cache ensures optimal autofocus and post-processing calibration.
When to Choose DIY Repair vs. Professional Electronic Device Repair?
Our free repair guides help you troubleshoot simple issues at home. Whether you want to know how to handle minor software glitches or basic maintenance, we provide step-by-step instructions. However, complex tasks like an iPhone screen replacement, battery replacement, or fixing a device that won't charge often require specialized tools and expertise.
Expert Phone Repair in Ljubljana and Maribor
If you are facing severe hardware issues—such as water damage, a laptop overheating, or an electric scooter that won't turn on—it is safer to rely on professional technicians. KRON Servis is your trusted partner for phone repair Slovenia, offering reliable services in two major cities: phone repair Ljubljana (Vilharjeva cesta 29) and handy reparatur Maribor (Zagrebška cesta 83a).
We specialize in a wide range of services, including laptop repair, computer service, PS5 and gaming console repair, TV repair, and household appliance servicing. We use OEM parts to ensure the highest quality, and every repair comes with a 12-month warranty. Diagnostics are priced at €30 including VAT.
Check our pricing page for details, track your repair status online, or reach out to us directly via our contact page for professional assistance.