Samsung Galaxy S26 Plus Screen Replacement
Replace the screen on your Samsung Galaxy S26 Plus if the Dynamic AMOLED display is cracked, exhibits dead pixels, displays vertical lines, or fails to respond to touch input. The repair requires opening the phone from the rear glass panel, disconnecting internal components, and swapping either the bare panel or the complete screen-and-frame chassis. Following this guide step by step ensures a clean, professional repair that restores full visual clarity and touch functionality.
Required Tools
- Heat gun, heating pad, or iOpener
- Suction handle
- Thin plastic opening picks and plastic spudger
- Phillips #00 precision screwdriver
- ESD-safe precision tweezers
- Isopropyl alcohol (90% or higher)
- Replacement Samsung Galaxy S26 Plus screen assembly (display with frame recommended)
- Pre-cut replacement rear glass adhesive
Step by step
- 1
Step 1: Power Down and Remove the SIM Tray
Turn off the Samsung Galaxy S26 Plus completely to avoid electrical shorts during disassembly.
Insert a SIM eject tool into the bottom hole to pop out and remove the SIM card tray.
- 2
Step 2: Heat the Rear Glass Panel
Apply uniform heat (approximately 75 to 80°C) around the perimeter of the back cover for 2 to 3 minutes to soften the factory adhesive.
Keep the heat source moving constantly to avoid scorching the glass finish or damaging internal sensors.
- 3
Step 3: Separate the Back Cover
Place a suction cup near the bottom edge of the back panel, pull upward gently to form a gap, and insert a plastic pick.
Slide the pick around the edges to slice through the adhesive, keeping the pick depth under 3 mm to avoid catching internal ribbon cables.
- 4
Step 4: Remove the Upper Bracket and Wireless Charging Coil
Use a Phillips #00 screwdriver to remove the screws securing the upper motherboard shield and wireless charging assembly.
Gently unclip the bracket, peel up the NFC and wireless charging pad, and set the assembly aside.
- 5
Step 5: Disconnect the Battery
Use the flat edge of a non-conductive plastic spudger to pry up the battery press-fit connector immediately.
Disconnecting the battery early eliminates any risk of shorting out delicate motherboard components while working.
- 6
Step 6: Remove the Lower Loudspeaker Assembly
Unscrew the Phillips #00 screws securing the bottom loudspeaker cover.
Lift out the speaker module to expose the daughterboard, USB-C connector, and lower flex cable connections.
- 7
Step 7: Disconnect Internal Ribbon Cables
Pry up the display flex cable, main-to-sub interconnect ribbons, and antenna lines from both the motherboard and lower daughterboard.
Carefully lift the coax connectors using fine-point tweezers to prevent tearing the fragile coaxial sockets.
- 8
Step 8: Remove the Motherboard and Sub-Board
Unscrew the retaining screw holding the motherboard in place, disconnect the front-facing camera, and carefully lift the main logic board out of the chassis.
Follow the same gentle extraction process to remove the lower USB-C sub-board.
- 9
Step 9: Transfer the Battery and Small Components
If you are installing a screen with a pre-fitted frame, transfer the vibration motor, earpiece speaker, and front camera into the new frame.
Apply a few drops of isopropyl alcohol around the battery cavity to soften the adhesive, then use a wide plastic pry tool to lift the battery out without puncturing or bending it.
- 10
Step 10: Reassemble Boards and Connectors
Seat the sub-board, motherboard, front camera, and battery securely into the new chassis.
Reconnect all flex cables and antenna connectors, pressing down until each snaps firmly into place.
- 11
Step 11: Test the Replacement Screen
Reconnect the battery cable, temporarily mount the top bracket, and turn the device on.
Test the touch responsiveness across the entire display, verify brightness levels, and check the front camera and proximity sensor before final sealing.
- 12
Step 12: Seal the Rear Glass
Power the device down and reinstall the upper and lower brackets with their Phillips screws.
Clean off any old adhesive residue from the back glass using isopropyl alcohol, apply the fresh pre-cut adhesive seal, and press the back cover firmly onto the chassis for several minutes to secure the bond.
Would you rather leave the repair to the experts?
Disclaimer: repairs are done at your own risk. Devices contain batteries and live components; improper handling can cause injury or fire. For a safe, warrantied repair, contact us.
Frequently asked questions
No, a hardware screen replacement does not wipe the internal flash storage. However, creating a full cloud or computer backup prior to any repair is always recommended to protect against accidental damage.
The device will resist light dust and minor splashes if fresh pre-cut adhesive is applied correctly, but factory-level IP water submersion ratings cannot be guaranteed once the original seal is broken.
A display pre-bonded to the frame simplifies the repair significantly because you only need to transfer internal modular parts, avoiding the risky and messy process of gluing a bare AMOLED panel onto the original frame.
Recalibrate the sensor through Samsung's built-in service test mode (accessible via the dialer on supported firmware) or delete and re-register your fingerprints in the device settings.
When to Choose DIY Repair vs. Professional Electronic Device Repair?
Our free repair guides help you troubleshoot simple issues at home. Whether you want to know how to handle minor software glitches or basic maintenance, we provide step-by-step instructions. However, complex tasks like an iPhone screen replacement, battery replacement, or fixing a device that won't charge often require specialized tools and expertise.
Expert Phone Repair in Ljubljana and Maribor
If you are facing severe hardware issues—such as water damage, a laptop overheating, or an electric scooter that won't turn on—it is safer to rely on professional technicians. KRON Servis is your trusted partner for phone repair Slovenia, offering reliable services in two major cities: phone repair Ljubljana (Vilharjeva cesta 29) and handy reparatur Maribor (Zagrebška cesta 83a).
We specialize in a wide range of services, including laptop repair, computer service, PS5 and gaming console repair, TV repair, and household appliance servicing. We use OEM parts to ensure the highest quality, and every repair comes with a 12-month warranty. Diagnostics are priced at €30 including VAT.
Check our pricing page for details, track your repair status online, or reach out to us directly via our contact page for professional assistance.