Skip to content
Repair Guides

Samsung Galaxy Z Flip7 Rear Camera Replacement

Moderate1-2 h10 steps

When your Samsung Galaxy Z Flip7 rear cameras produce blurry images, fail to focus, or show a completely black screen, a camera module replacement is usually necessary. This repair involves entering the device through the upper back glass panel which houses the delicate cover screen. You will need a steady hand and patience to safely navigate the internal components without damaging the flexible display cables.

Required Tools

  • Heat gun or heating pad
  • Suction cup
  • Plastic guitar picks and spudgers
  • Precision Phillips screwdriver set
  • Tweezers
  • Isopropyl alcohol (99 percent concentration)
  • Precut adhesive strips for the upper back panel
  • Anti-static wrist strap

Step by step

  1. 1

    Step 1: Power Off the Device

    Always begin by completely powering down your foldable phone to prevent electrical shorts.

    Wear an anti-static wrist strap to protect the sensitive internal components from static discharge.

  2. 2

    Step 2: Heat the Upper Back Panel

    Apply gentle heat to the upper rear glass panel using a heat gun or heating pad to soften the factory adhesive.

    Keep the heat moving constantly to avoid burning the cover screen display underneath the glass.

  3. 3

    Step 3: Slice the Adhesive

    Place a suction cup near the edge of the heated upper glass and pull up slightly to create a tiny gap.

    Insert a plastic guitar pick into this gap and carefully slide it around the perimeter to cut through the adhesive.

  4. 4

    Step 4: Disconnect the Cover Screen

    Lift the upper glass panel very slowly like a book to reveal the cover screen flex cable connected to the motherboard.

    Use a plastic spudger to gently pop the connector off its socket before completely setting the upper panel aside.

  5. 5

    Step 5: Remove the Motherboard Shield

    Locate the protective metal shield covering the main motherboard and battery connectors.

    Unscrew the Phillips screws securing this bracket and lift it out of the device with tweezers.

  6. 6

    Step 6: Disconnect the Batteries

    Safety is paramount when working inside modern smartphones.

    Use your plastic spudger to immediately disconnect both battery flex cables from the motherboard to ensure no power is flowing through the board.

  7. 7

    Step 7: Extract the Faulty Camera Module

    Locate the rear camera module and use a spudger to disconnect its flex cables from the motherboard.

    Carefully pry the old camera unit out of its housing using tweezers.

  8. 8

    Step 8: Install the New Camera

    Seat the replacement camera module into the empty housing and ensure it sits perfectly flush.

    Gently press the new camera flex cables down onto their motherboard sockets until they click securely into place.

  9. 9

    Step 9: Reconnect Power and Test

    Reconnect both battery flex cables and temporarily attach the cover screen cable to test the device.

    Power the phone on and open the camera application to verify that the new lenses focus correctly and produce clear images.

  10. 10

    Step 10: Seal the Device

    Once testing is successful, power the phone back down and reinstall the metal motherboard shield with its screws.

    Clean the old adhesive off the frame with isopropyl alcohol, apply new precut adhesive strips, and firmly press the upper back glass panel back into place.

Safety

Would you rather leave the repair to the experts?

Disclaimer: repairs are done at your own risk. Devices contain batteries and live components; improper handling can cause injury or fire. For a safe, warrantied repair, contact us.

Frequently asked questions

If only the exterior glass covering the lens is cracked but the camera still takes perfect photos, you only need to replace the external lens cover. However, if the camera itself is damaged or has dust inside the sensor, you must replace the entire internal camera module.

Yes, breaking the original factory seal will compromise the water resistance of your foldable device. You must apply high-quality replacement adhesive during reassembly to restore as much protection as possible.

The Galaxy Z Flip7 utilizes a dual-battery system with a cell in both the top and bottom halves of the phone. Disconnecting both ensures the motherboard is completely isolated from power, which prevents accidental short circuits during the repair.

You should strictly avoid using metal tools to pry the glass panels. Metal can easily scratch the aluminum frame, crack the glass, or sever the delicate cover screen flex cable hidden underneath.

Back to Guides

  • 12-month warranty
  • Original (OEM) parts
  • Your data kept confidential
  • You approve the price before the repair
  • 3,486+ devices per month