Skip to content
Repair Guides

Samsung Galaxy Z Fold7 Camera Replacement

Difficult1–2 h11 steps

Is your Samsung Galaxy Z Fold7 taking blurry photos, failing to focus, or showing a blank screen when you open the camera app? These symptoms indicate that the massive 200MP rear camera module may be damaged and requires a replacement. Repairing this specific foldable device is notoriously difficult and requires extreme patience due to its extremely thin design and fragile internal components. This guide will walk you through safely opening the back panel and swapping out the faulty camera assembly without damaging the rest of the phone.

Required Tools

  • Heat gun or heating pad
  • Suction cup handle
  • Thin plastic opening picks
  • Plastic spudger tool
  • Phillips #00 screwdriver
  • Tweezers
  • Replacement camera module
  • Precut waterproof adhesive for the back glass

Step by step

  1. 1

    Step 1: Power Off and Heat the Back Panel

    Turn off your Galaxy Z Fold7 completely before starting.

    Apply a heat gun or heating pad to the rear glass panel for about three minutes to soften the waterproof adhesive.

  2. 2

    Step 2: Create an Opening Gap

    Apply a suction cup to the lower portion of the back glass and pull up gently.

    Insert a thin plastic pick into the gap you create to prevent the adhesive from resealing.

  3. 3

    Step 3: Slice the Perimeter Adhesive

    Slide the plastic pick around the edges of the back glass to cut through the softened adhesive.

    Avoid inserting the pick too deeply near the massive camera bump to prevent damaging internal flex cables.

  4. 4

    Step 4: Remove the Back Glass

    Once all adhesive is cut, carefully lift the back glass away from the device.

    Set it aside in a safe place where it will not get scratched or broken.

  5. 5

    Step 5: Remove the Motherboard Shield

    Unscrew the Phillips screws securing the plastic motherboard shield and NFC antenna.

    Gently pry up the shield and remove it to expose the main board and battery connectors.

  6. 6

    Step 6: Disconnect the Batteries

    Using a plastic spudger, immediately disconnect both battery flex cables from the motherboard.

    The Z Fold7 features a complex dual battery design, and disconnecting power is a crucial safety step to prevent short circuits.

  7. 7

    Step 7: Disconnect the Camera Module

    Locate the flex cables connecting the rear camera assembly to the motherboard.

    Carefully pry up the connectors with your plastic spudger to detach the cameras.

  8. 8

    Step 8: Extract the Old Camera Assembly

    The camera module is usually held in place with a small amount of adhesive and a retaining screw.

    Remove any screws, then gently pry the camera module out of its housing.

  9. 9

    Step 9: Install the New Camera Module

    Seat your replacement camera assembly into the housing and press down gently.

    Reconnect the camera flex cables to the motherboard securely.

  10. 10

    Step 10: Reconnect Batteries and Shield

    Snap the battery connectors back into place on the motherboard.

    Reinstall the motherboard shield and secure it with the Phillips screws.

  11. 11

    Step 11: Seal and Reattach the Back Glass

    Apply new waterproof adhesive tape to the perimeter of the phone frame.

    Press the back glass firmly into place and apply steady pressure for a few minutes to ensure a tight seal.

Safety

Would you rather leave the repair to the experts?

Disclaimer: repairs are done at your own risk. Devices contain batteries and live components; improper handling can cause injury or fire. For a safe, warrantied repair, contact us.

Frequently asked questions

The factory water resistance seal is broken when you open the phone. You must apply new precut adhesive perfectly to regain some water resistance, but it is never guaranteed to match the factory seal.

No, the rear cameras are accessible entirely through the outer back glass panel. You do not need to interact with the fragile inner folding display.

Ensure that you removed all protective plastic films from the new camera lenses before installation. If the issue persists, check that the flex cables are seated firmly on the motherboard.

The rear camera system on this device is built as a single interconnected module. You must replace the entire assembly even if only one specific lens is failing.

Back to Guides

  • 12-month warranty
  • Original (OEM) parts
  • Your data kept confidential
  • You approve the price before the repair
  • 3,486+ devices per month